Your computer will automatically reboot. It installed a Boot Menu with no touch-screen support. I have been working with laptops for the past 20 years so I am fairly conversant with their inner parts. The steps below are mentioned for both, desktop computers and laptops. On the initial try the power button light displays normally. Remember, your warranty voids if you open your laptop.
If the battery dies during this process the device could be damaged. I also attempted to Flash the Bios from Windows but that too failed. In this case we use another method. Otherwise, we will assume that you - revocable at any time for the future - agree to this data processing. Static discharges can damage your computer.
Open the hard drive compartment by sliding the cover out. Otherwise, repeat the steps above and try again. That battery is the same one as I disconnected. Instead of listing them all here, check out this that has a list of all the default passwords. Though it is a scare thing when you forgot the bios password, you still have chances to recover it with the steps shared in this tutorial.
I also attempted to Flash the Bios from Windows but that too failed. I do hope that this will at least get you going again. It is usually close to the battery. So now I have no way of running anything at all. Thank you so much for this tool! Touch the chassis of the casing with a metallic object to discharge static electricity. Power off the computer, insert all hardware components and restart the computer.
This Ebook has articles with photos and videos that show detailed step by step pc repair and maintenance procedures. No need to pay expensive fees to experts. To remove the password, leave these two fields blank and press Enter. You have to keep tapping as soon as you see a logo or life! The usb flashes once when power cord is plugged in, then nothing. Acer: Aspire One 552 Service Guide; Resources. So I would suggest you the 1st method. A jumper is a small, rectangular cap made of plastic that covers two jumper pins.
The best place to look is around the edges of the motherboard first. If you cannot locate this jumper, you might short both of the points where the battery connects to the motherboard. A jumper is basically a number of pins sticking out of the motherboard with a small piece of plastic covering some of the pins. Delicious ; Digg ; Facebook ; Apr 16, 2016 I know some methods to reset bios password. I tried the Generic Phoenix password on my laptop and it worked! This may also void your warranty period. If there are only two pins for the jumper, just remove the cover completely. Posted on Mar 01, 2012 Step 1: The Acer Aspire stores the password in a component called the complementary metal-oxide semiconductor.
In the , they show where the battery is located and how to remove it. This has worked on every laptop that I've serviced, even new models. Note that you need to install Acer Empowering Technology first. Acer is a leading computer hardware manufacturer. In some cases, you will have to remove the jumper while the system is powered up, though to minimize risk, try doing this first with the computer off. Unscrew and pull out the hard drive from your laptop. Notebooks don't have any jumper.
I have no clue as to what the password is. Subscribe Subscribed Unsubscribe 4,157 4K. Then release the power button only. When a password was set, you will be promoted to enter the right password in next time you access it. Any suggestions as to what is happening here? Look at the picture below. Then, slide the keyboard up and out to remove it. There will be 3 pins and the jumper will be joining the center pin to either left or right pin.
This is done by moving a jumper on the motherboard. Wait a few seconds, and then put them back in its original position. Removal is accomplished by pushing down on the tab securing the battery to the motherboard and lifting the battery out of its slot. Now it has zero vital signs: No power light, no fan, no booting of any kind. I have also removed all hard drives etc. Remove the jumper shunt from pin 1 and pin 2; then place the shunt on pin 2 and pin 3. Put it back after a few minutes.
Its very interesting the info you have published. You can then put the jumper back into its original position. The key you're prompted to press might also be different; if so, use that key instead. Wait a few seconds, and then put back the to its original pin 1-pin 2 position. Windows especially Win10 goes to great lengths to prevent nearly all low-level access to the system through it. So now I have no way of running anything at all. Last Updated on Sat, 10 Nov 2018 This section provides you the standard operating procedures of clearing password and for.