Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover. The vehicle can move forward or backward. Depending upon the type and placement of the load, hauling cargo and people may raise the center of gravity of the vehicle. To avoid risk of injury, occupants should only use seating positions where they are able to be properly restrained. When your vehicle is not moving, this function shows , one or no bars illuminated.
Inflate all the tires to the recommended inflation pressure. Make sure the headlamps and vehicle accessories are off. Set the parking brake and ensure the gearshift is securely latched in P Park. Turn the steering wheel one-half turn to access the slots on each side of the steering wheel. Remove the jumper cable from the ground metal surface. Contact your authorized dealer or a reliable trailer dealer as soon as possible if you require assistance. Used engine coolant should be disposed of in an appropriate manner.
This will ensure that the cleat is properly oriented to accept accessory attachments. These items can then be slid to either side, and secured the same way as the side rails. This must be done within five seconds of completing Step 1. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Press and hold to exit phone mode or end a call. Pull out the old bulb from the socket and push in the new bulb.
To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. Failure to follow these instructions may interfere with the front passenger seat sensing system. Note: The Box Side Step load carrying capability 1 person + cargo is 500 lbs 227 kg. Changes to towing conditions include trailer load, vehicle load, road conditions and weather. Washer fluid placed in the cooling system may harm engine and cooling system components. Enter factory—set 5—digit entry code. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage.
Don't waste time calling around to your local bookstores or waiting for a repair manual to arrive by mail. The emission system heats up the engine compartment and exhaust system, which can start a fire. Note: Cranking may be stopped at any time by turning the key to the off position. Select the autolamps by turning the headlamp switch to Steps 2 through 5 must be performed within a 10 second period. The shoulder belt must be snug to keep the lap belt tight during a collision. The system will automatically provide outside air to reduce window fogging.
The tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc. Ford may change the contents without notice and without incurring obligation. Do not exceed 500 lbs 227 kg. Vehicle line, series, body type 4. Refer to scheduled maintenance information. Rotate the panels toward the tailgate. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Install a new air filter element. Press the control to recline the seatback forward or rearward. Remove the air filter element from the air filter housing. Use with recirculated air to improve cooling performance and efficiency. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. Ford recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. Note: The seat will not travel to its final position if the key is not in the ignition and the easy entry feature is enabled.
Accelerate to the desired speed. Ford Motor Company shall not be responsible for any such programming changes. In the event that there are still programming difficulties, contact HomeLink at www. Again, avoid these abrupt inputs. Make sure that the seat is relatched into place. If the light fails to display when the ignition is turned on, or remains on, have the system serviced immediately by your authorized dealer.
Vehicle Curb Weight — is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Note: Some noise may be heard as the system shifts or engages; this is normal. Turn the ignition to the on position; the horn will chirp to indicate the driver configuration mode has been activated. Pull up the head restraint until it reaches the highest adjustment position. This noise can be alleviated by lowering a front window approximately two to three inches.
The system is working properly. Refer to the instruction sheet located with the jack for detailed tire change instructions. Use only Ford recommended replacement fasteners. Using a screwdriver or similar tool, remove the protective cover to the interlock release access hole, located to the right of the gearshift lever. Note: In the illustrations, lightning bolts are used to designate the assisting boosting battery. Refer to Heated and cooled seats in the Seating and Safety Restraints chapter for more information. Pull the lever towards you to deactivate.