Body and Frame 2007 Chevrolet Cobalt Body and Frame Consumer Complaints Complaint Number: 10399079 Incident Date: May 4, 2011 Date Added to File: May 4, 2011 Description of the Complaint: I have a 2007 chevy cobalt with a leaking sunroof. Return the headliner to its original position and reinstall the trim to secure the headliner in place. Maintain Your Sunroof Inspect the exterior of your sunroof of your Ford Explorer on a monthly basis. Install the new rubber seal into the channel, beginning with the outer lip and then moving to the inner lip. Unplug your sunroof's power source. I like the compressed air and pouring water into the channel idea also sounds easier than dropping the headliner.
Take photographs to refer to later, so you can easily replace the sections when your repairs are complete. Use the plastic scraping tool to lift off the old rubber seal. I had mold and moss growing on mine. I've owned my cars for twelve years and have never had any problems with any of my vehicles please help me understand having such major problems like this with a brand new car that I've had for three years. If you see such warping, it's an indication the tracks need cleaning, or that the rubber seal needs to be replaced. Be sure to order for side you need.
It is the cowel's job to prevent water from entering this part of the vehicle. Remove the interior trim and allow the cloth that covers the ceiling of your Chevy Cobalt to drop down so you can access the tracks to your sunroof. Keep checking to make sure it's level. Refer to the picture you took earlier to ensure each is properly repositioned. Place the sunroof back on top of the truck and reconnect it using the screws and bolts you removed earlier.
Use your plastic scraper if needed. Purchase a rubber seal for your Cadillac Escalade model year. Check for wrinkles and gaps. Clean the sunroof's rubber seal with a clean, damp, lint-free cloth. Unplug the sunroof from its power source, located at the back of the sunroof.
The cars cooling system directs hot coolant to it so you can have heat. Set your sunroof back in place and secure it using the screws, bolts and clips you removed in Step 2. The heater core is located under the dash, passenger side, it's like a mini radiator. This website does not reflect our current on hand inventory. Use a plastic scraper to remove any remaining rubber or adhesive.
The fumes from some of the products are meant to be used under the hood and not inside the cabin where the people are. Use compressed air to blow out any debris, dust or clogs. I know it's not coolant, just dirty water. Remove all the screws, clips and bolts that hold your sunroof to the body of your vehicle. At the bottom front corner of the front doors the carpet has a plastic hook that is around one of the trim clips. Removing the plastic trim around the door if you grasp the trip peices firmly they just pull up off some metal clips,but they can be quite stubborn you will notice the carpet just pulls up. Let me know what u find Curt Mar 18, 2009.
Note that two of these tubes drain to the front of your vehicle. Remove each tube from its spout and use compressed air to remove any buildup or debris that may block the flow of water. But you would want something like the glass shops use. You may need the help of another person for this task, to avoid damaging the sunroof or the truck. Also, the carpet edges and some of the more hidden panel clips are very sharp and may cut you while you are poking around, so be carefull.
Lubricate the tracks that allow your sunroof to slide open. Use compressed air to remove debris, then lubricate the tracks with 3-In-One lubricant. Jun 18, 2013 Hello, You may have a potential claim under your Car Insurance for Comprehensive which may have no deductible. Use compressed air to blow out debris and lubricate the tracks with 3-in-One Lubricant. Check thoroughly for any wrinkles or gaps, and reinstall the seal in those spots.
Any suggestions would be greatly appreciated. Two drain to the rear, usually behind the tail lights. Lift the gasket and reinstall it at those locations until the liner lays smoothly and evenly in the channel. The illustrations in this catalog are to be used as a guide only. Lubricate and clean your rubber gasket.